Hit Enter to search or Esc key to close

Ask MetaFilter. We are purchasing a fridge that is new make use of the «Cash for Clunkers for Appliances» program.

Ask MetaFilter. We are purchasing a fridge that is new make use of the «Cash for Clunkers for Appliances» program.


Ask MetaFilter. We are purchasing a fridge that is new make use of the «Cash for Clunkers for Appliances» program.

We are investing in a fridge that is new make use of the «Cash for Clunkers for Appliances» program.

Brand brand New fridge we wish has an ice manufacturer, which clearly (right?) is certainly going to need a water hookup that our present suck-ass Magic Chef doesn’t. Exactly how much of an issue (in work and value; we’re in Brooklyn, NY) will it be to include a hookup that is new? It is close to our drain, so that the pipelines should be there.

If, for reasons uknown, it isn’t practical getting the work done, can there be any explanation we could not simply connect within the refrigerator sans-ice manufacturer, and later hook it up?

you need to be able to install the manual on the internet. Observe how the instructions read.

We suspect it should be since straightforward as placing a T on the chilled water line and operating a plastic that is small towards the straight back for the refrigerator. but. IANAP posted by HuronBob at 2:42 PM on February 11, 2010

Home Depot offers a kit because of this. It is simply just a little needle thing that taps into the pipe that is existing. I do believe it is a somewhat various kit based on when you have copper or PVC.

Yeah, then drill a hole in the cabinet to run the line if the fridge is going in right next to the sink, I would use a saddle valve on the cold line to the sink. You ought to be in a position to do all the work (with the exception of drilling the opening) with fundamental hand tools plus some sense that is common.

1) If you have not really bought yet, i do want to emphatically endorse investing in a model aided by the fridge in the bottom. It really is Hence really nice getting the meals you access most there be right up right in front of one’s face.

2) setting up an ice manufacturer line must not be too much. My hubby recently changed ours out from a copper line to a single of the lines that seems like a fuel pipe (bendy and much more durable because our copper line create a kink inside it and leaked). With respect to the kind of line you employ, you may need to make numerous, numerous batches of ice because you can «taste» the plastic or whatever the line is made of that you throw away. maybe Not an issue, only a pain you about that I thought I’d warn. published by wwartorff at 3:26 PM on February 11, https://besthookupwebsites.net/escort/colorado-springs/ 2010

«If, for reasons uknown, it is not practical to obtain the work done, can there be any explanation we could not just connect into the refrigerator sans-ice manufacturer, and connect it later on? «

Not a problem just exactly what therefore ever; just be sure you Ice Maker is within the position that is off it doesn’t cycle all of the type.

jon1270 writes » For an ice manufacturer, a seat valve must be enough.»

Saddle valves are virtually guaranteed in full to leak at some time later on; specially under a sink where they’ve been put through technical harm. Better is either a Compression Tee/Quick tee adaptor or a turn off valve with two ports whenever you can find one which fits your water sink that is cold shutoff. Either may be set up with only a few wrenches and perchance a pipe cutter.

The ice maker install kits will have either synthetic or copper tubing. The copper tubing is more high priced but less inclined to be catastrophically damaged. You can when you run the line drill the hole in the cabinet as close to the floor and wall as. Then make a sizable loop that is complete the tubing (roughly because big across given that width associated with the refrigerator; 5-7′ of line) before connecting the finish associated with the tubing towards the water valve regarding the refrigerator. The cycle shall lay flat up against the wall surface behind the refrigerator and invite you to definitely pull the fridge right out of the wall surface without damaging the tubing. Be sure the clamp is used by you that accompany the kit to connect the tubing to your refrigerator near it is valve so that the valve does not get damaged.

Then you should install an inline sediment filter if your water contains appreciable sediment (check for mud in the bottom of your toilet tank) and your fridge also dispenses chilled water. Otherwise that muck leads to the cold dish that chills water. published by Mitheral at 3:44 PM on February 11, 2010 [2 favorites]

First thing you must do is always to look underneath the sink and discover which kind of supply visits the water that is cold. When it is a body that is valve versatile lines running up, verify that the threads at the top are standard half inch pipeline threads. If that’s the case, you are able to unscrew water line towards the sink and install an easy tee over the valve, re-install the water line and then install the kit-based line to your refrigerator. Needless to say you will have turned water off before unscrewing such a thing. Appropriate?

Simply just simply Take a mobile phone picture of what exactly is beneath the sink and show it to your plumbing work «expert» in the home Depot or Lowes and s/he can explain to you all the goodies you will need. As happens to be noted above, the hardest component is drilling for the line through the case and that is actually no big deal. I elect to drill only a little bigger hole than is necessary therefore feeding the ice-maker line through is only a little easier. Additionally, drill this hole dating back to feasible, therefore the line does not interfere aided by the material you retain within the case. published by Old Geezer at 4:40 PM on February 11, 2010